Showing 16 items matching steel’s creek
-
Kiewa Valley Historical Society
Core Rock Samples
The core samples in the display cabinet were obtained from the various sites at which drilling into the rock surface was carried out (under the control of design and structural engineers of the SEC Kiewa Hydro Scheme - late 1940's). This function was a precursor to the decision where to locate, in this case, the McKay Creek Power Station. The information gained by structural engineers from the core samples would be used also for the placements of underground tunnels entry and exit points and the overall effective size of the generator plant. This would have included drill and blast techniques (rock characteristics play an import part of explosion control), requirements for support structures and reinforcing cement/steel forms. The use and replenishment of diamond drill bits(the strongest available, see KVHS 0280) was dependent on the "type" of rock found (harder rock required greater numbers of drill bits). Support beams for reinforced ceilings and floors was also a necessity.These rock core samples are very significant in the formulation and placement of the underground Power Stations and their maze of tunnels (in and out) for a successful implementation of the Hydro Scheme. The amount of pre-planning and engineering studies required for such a large scheme must be undertaken to ensure that a "white elephant" was not the result.There are nine columns of rock cores, each 30mm in diameter, set in a wooden display rack. A clear plastic (slide out) protective panel is installed to the front section. Within each column are block details of the depth from which that section was brought from. See KVHS for the appropriate sketch details.Depth levels (retrieved from) are shown for each section on wooden Blocks: 1st Block: "7'10" (seven feet, ten inches), 2nd Block:"9'4" (nine feet, four inches), 3rd Block: "19'3" (nineteen feet, three inches), 4th Block: "24'2" (twenty four feet, two inches), 5th Block: "25'7"( twenty five feet, seven inches) and last block: "30' (thirty feet)"alternate energy supplies, alpine feasibility studies temperature, rainfall, sec, kiewa hydro scheme, electricity -
Kiewa Valley Historical Society
Pair of vehicle wheel traction devices
This traction device was made to increase traction and braking on slippery surfaces eg. snow / ice and can be fitted on two wheels on one or more axles of a vehicle. These devices can fit many wheel sizes. these 'snow chains' were used in the early 1970's.These vehicle traction devices were used at Falls Creek during winter.Rusted steel device used to grip vehicle wheels to enable traction over slippery surfaces. Four steel curved prongs connected at a solid steel rectangular centre. Each prong has teeth at the centre enabling it to fit through and be moved for tightening. The prongs are at 90 degrees to each other. The steel prongs are 'waved' on the outer wheel where they contact the surface of the ground. On the outside of the centre piece a coiled piece of steel is attached extending out to curve around one of the prongs Inside centre on steel rectangular plate: "Christiana Spigervek" / "Norway Patent Nos. 116148 / 116188 / Norway / Foreign Patents Pending."snow chain; vehicle traction device; falls creek -
Orbost & District Historical Society
bread knife
This knife was used by Lottie Rem who ran the cookhouse at Astergren;s Timber Mill at Cabbage Tree in East Gippsland from 1954 until 1966.. It was bought in Orbost around 1957 - 1958. Sited on the banks of the Cabbage Tree Creek, the township was built by the timber mills to house their workers. Although the timber mills have disappeared, some of the buildings still remain. The "Cook House" and "Manager's House" are two buildings. The Cook House was built to supply meals to the workers of the Alstergren Mill. Some of the original interior walls were made from hessian and wallpaper. The few houses to survive to today are now used as private dwellings.The Cabbage Tree Creek township was established to support the booming timber industry of the mid 20th century. Five timber mills worked full time supporting the families that were drawn to the area's wealth of natural resources. this item is associated with the history of Cabbage Tree.A stainless steel serrated edged knife with a cream coloured handle (bone?)on blade -""Made in Sheffield expressly for Orbost Hardware and Timber Co, Orbost"alstergren-timber-cabbage-tree rem-lottie cook-house-alstergren's-timber-mill bread-knife-orbost-hardware -
Puffing Billy Railway
Floodlight Projector, Tilley Model FL6, circa 1940's
Tilley Floodlight Projector - Model FL6 It stands about a metre high, and when lit, turns out about 5,000 candle power from the parabolic mirror in the back of the lamp. manufactured between the mid 1940's and early '50's It runs on kerosene that is pressurized with the integral pump, to provide a light beam from the parabolic mirror in the back of the lamp of approximately 3,000 candle power which can project over 1/4 of a mile. It features a pressure gauge, armored glass and all steel construction. Historic - Railways - Tilley Floodlight ProjectorTilley Floodlight Projector - Model FL6 made of metal, brass and glass and steelTilley Floodlight Projector - Model FL6puffing billy, tilley floodlight projector -
Puffing Billy Railway
Blackstone Oil Engine, 6 November 1908
8HP Blackstone Lamps Start Oil Engine engine number 71076 Engine Details Maximum operating RPM of 240. Fitted with a 3'9" Flywheel Tested on the 6th of November 1908. Shipped to Cluter buck South Australia for installation on concrete base. Recovered and restored during the 80's in South Australia Purchased privately in 2013 in Tailem Bend South Australia and transported to Victoria. Currently on loan to the Puffing Billy Museum at Menzies Creek as an operating exhibit. Blackstone & Co. was a farm implement maker at Stamford, Lincolnshire, United Kingdom. In 1896 they built lamp start oil engines. The Lamp or hot-bulb engine (also hotbulb or heavy-oil engine) is a type of internal combustion engine. It is an engine in which fuel is ignited by being brought into contact with a red-hot metal surface inside a bulb, followed by the introduction of air (oxygen) compressed into the hot-bulb chamber by the rising piston. There is some ignition when the fuel is introduced, but it quickly uses up the available oxygen in the bulb. Vigorous ignition takes place only when sufficient oxygen is supplied to the hot-bulb chamber on the compression stroke of the engine. Most hot-bulb engines were produced as one-cylinder, low-speed two-stroke crankcase scavenged units Historic - Industrial - single cylinder, horizontal, 4 stroke, hot-bulb ignition oil engine Blackstone 8HP Oil Engine made from steel, wrought iron and brassOval Plate with Black Stones and Clutter Buck Brass Plaque engine number 71076blackstone, oil engine, clutter buck, black stone, puffing billy, hit and miss, engine, blackstone & co -
Puffing Billy Railway
Victorian Railways 2'6" Transporter wagon 129Q, 1926
The Q class were introduced as bogie flatwagons in the 1870's. Large Q wagons as shown were built to the 1920's In the early 1900's, some Q wagons were modified for Pintsch Gas traffic with a small pump motor cabin at one end and a tank for carrying the gas. Other conversions for traffic were as required. Examples were: sheet glass, skeletal underframes between workshops In 1926 the railways built two narrow gauge Garratt locomotives. As normal wagons were unsuitable for moving these locomotives a special skeletal wagon was built. The engines were split into units for transportation. It featured axle bearings and boxes from steam engines, had hinged buffers that could drop out of the way during loading/unloading. It also featured 'strap' rail along the deck. The wagon was Q 129. This wagon was also available for general narrow gauge rolling stock. Q wagons were numbered from 1 to 136. Service History: *Q 129.VA - 1/ 6/1926 NWS Built new H/brake & drop buffers. For traffic of Narrow Guage stock 31/ 1/1931 NWS Into Workshops - 16/ 6/1931 NWS Out of Workshops (50 days) 6/11/1931 NWS Into Workshops - 27/11/1931 NWS Out of Workshops (22 days) 24/ 8/1936 NWS Into Workshops - 10/ 9/1936 NWS Out of Workshops (18 days) 27/11/1936 NWS Into Workshops - 26/ 2/1937 NWS Out of Workshops (Light repairs) circa 1960 - Photograph SL20 p32, loaded with 7NA / /1975 - Photograph #393 / /1976 - Photograph #553, #554 19/ 3/1979 - Condemned - 10/ 4/1979 - Off Register - 10/ 4/1979 - Sold (to) ETR, Belgrave / /1989 EME Body [GRE]. [SXC]: 29/3/92, MEL127E5, Puffing Billy at station Historic - Victorian Railways - Transporter wagon used to carry and transfer 2' 6" Narrow gauge rolling stock over Victorian broad gauge (1,600 mm (5 ft 3 in) main lines to the narrow gauge lines. Q 129 was unique, it was built to transport narrow gauge locomotives. Transporter Wagon made of Steel and wrought Iron129Q129q, puffing billy, transporter wagon -
Puffing Billy Railway
Number Plate - 6A, 2010
Replica of a Victorian Railways replacement number board that 6A carried in the later 40's and 50's. This plate was created for the preservation society's reenactment trains in 2012 for the 50 year celebration of reopening to Menzies Creek. Loco: 6A In service Thursday, 18th July 1901 Livery Green Owner Puffing Billy Gauge 762 Status Preserved - Operational 6A Built in 1901 and painted two-tone green, this locomotive was issued to the Colac to Beech Forest line and was used in that line’s construction. Over the years, it saw service on all four lines, but mostly on the Colac to Crowes and Upper Fern Tree Gully to Gembrook lines. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it saw almost continuous service until being withdrawn in 1983. It has been restored, as far as possible, to its original condition with original design side tanks, low bunker, original size windows, etc., but a steel cow-catcher in place of the original style wooden one. It also has its original colour scheme of two-tone green with white lining.Historic - Replica Victorian Railways Locomotive Number Plate of the type used on Steam Locomotive 6A in the later 40's and 50's created for the preservation society's reenactment trains in 2012 for the 50 year celebration of reopening to Menzies Creek. Number Plate 6A Cast aluminum replica number board.6Apuffing billy, menzies creek, 6a, number plate -
Puffing Billy Railway
Vertical Pump, Weir, 1948
Weir Pumps - these types of vertical pumps were used extensively with both land and marine steam pumps. The pumps were also used for various duties from pumping oil fuel and feed water for boilers, to draining bilges on steam ship[s They are a single cylinder, double acting vertical pumps used by G. & J. Weir Ltd. , of Cathcart, Glasgow The large pump serial number 231703 was built in 1948 and worked at the old Victoria Brewery in East Melbourne before coming to the Museum in 1985. Historic - Weir Vertical Pump used at the old Victoria Brewery in East Melbourne The large pump serial number 231703 was built in 1948 and worked at the old Victoria Brewery in East Melbourne before coming to the Museum in 1985.Weir Vertical Pump - Large Steel PumpWeir puffing billy, weir vertical pump, victoria brewery -
Puffing Billy Railway
Weir Pump ( no. 2 ), Vertical ( no. 2 )
Weir Vertical Pump Weir Pumps - these types of vertical pumps were used extensively with both land and marine steam pumps. The pumps were also used for various duties from pumping oil fuel and feed water for boilers, to draining bilges on steam ship[s single cylinder, double acting vertical pumps used by G. & J. Weir Ltd. , of Cathcart, Glasgow .Weir Vertical Pump ( no. 2 ) - Steel vertical pumpWeirpuffing billy, fluid pump, weir, vetical pump -
Puffing Billy Railway
Clarkat Tug Locomotive, 13 April 1943
Clarkat A Clarkat Aircraft Tug that has been converted to run on Rails, This Clarkat 'B' was one of 11 machines shipped on 13 April 1943 to the Lathrop Holding & Re-consignment Depot in Lathrop, California. and was used at Jack's Magazine, Maibyrnong, Victoria and later on at Coal Creek Historical Village, Gippsland, Victoria. Clarkat Tug Model C S/N Cx30F Made by Clark Tructractor Div of Clark Equipment Co Battle Creek Michigan U.S.A Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 Historic - Industrial Narrow gauge railway equipment - Jack's Magazine, Maribyrnong, Victoria, Australia Clarkat Aircraft Tug that has been converted to run on Rails, made of steel Coal Creek Tug Clarkat Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 clarkat, clarkat aircraft tug, puffing billy, jack's magazine -
Hepburn Shire Council Art and Heritage Collection
Public Art Work, 'Bunjil' - Russell Petherbridge. 2012, 2012
'Hepburn Pool is a forgotten treasure which many visitors to Hepburn Springs would never be aware of. The owners of the Bellinzona Grange hotel explained that it was once the hotel pool and was built in the 1930's. You can find it behind this hotel, downhill at a street called The Pool Way. Steps and a ramp continue down to the pool itself and the secluded park around it. It was built into Spring Creek and became a competition pool for state swimming championships. A concrete weir separates a shallow children's pool from the main pool. You can still see the numbers of each lane painted on the walls at the deep end. There are plenty of seats and a barbeque area. A sign says this is a sacred aboriginal spot and you can certainly feel something magical about the place. I wouldn't suggest swimming in the former pool, it looks rather murky now.' Review of Hepburn Pool by 'Jolyon67' on 'Tripadvisor', 3 June 2015'The Bunji: The Bunjil sculpture emerged from discussions with local indigneous Elders, as a dreamtime totem to the Sacred Pool at Hepburn Springs. The original idea was to create the 3 totems of the area...the Bunjil, The Crow and The Bat. Russell applied for, a council grant of $3,000 to design, create and install the Bunjil Sculpture to overlook the pool and reflect its powerful image in the water.' Information provided by Russell Petherbridge, December 2015Large scale steel sculpture depicting 'Bunjil', the dreamtime totem of the Hepburn Pool, an eagle in flight.art, public art, sculpture, installation art, aboriginal art, site specific art, hepburn shire, hepburn shire public art collection, russell petherbridge, bunjil, hepburn, hepburn pool, aboriginal significance, steel sculpture -
Coal Creek Community Park & Museum
Terrestrite measuring equipment, 1888 (Approx)
8382.1 - Metal (likely steel) protractor, marked down to 0.5, used mostly in map drafting. 8382.2 - Wooden red velvet-lined case.- Flavelle bros and Roberts, Sydney and Brisbane. - 6692 a s x- similar marks were made and scratched out. - a h x -
Whitehorse Historical Society Inc.
Article, News pioneer dies, 2001
Obituary for Ethel Steel.Obituary for Ethel Steel. She and her husband, Les founded the early Whitehorse paper, 'The Local Advertiser' in the mid 1950's. Their son, Barry also worked on the paper as a printer. She was a volunteer at Box Hill Hospital for 25 years.Obituary for Ethel Steel. newspapers, the local advertiser, steel, ethel, steel, les, steel, barry, box hill hospital -
Whitehorse Historical Society Inc.
Accessory - Shoe Horn
Collection of Dorothy WilliamsSilver plated shoe horn, pear shaped handleMade in England, Steel, Hallmark: S & Co, flower, lion, h, 2 other Hallmarks worn - indecipherabledomestic items, appliances, costume accessories, footwear accessories -
Whitehorse Historical Society Inc.
Tool - Pliers, c 1920
Watchmaker's tool used by W.R. Cruickshank from 1920 -1970's in Albury when he worked for Nicholson & Smith, Watchmakers and JewellersSteel pliers pointed at nose. Handles curved at different angleshorology, tools -
Whitehorse Historical Society Inc.
Tool - Engineer,s Cold Chisel
Drawn Steel Tool with blunt cutting edge at one end and round top at the other.trades, metalworking, mechanics